2X Rear Wheel Bearing Hub Assembly W/ABS For 2011-2018 Ford Fiesta 1.6L HA590367

Description

Item Description:
Item Features
Condition:New
Placement on Vehicle：Driver Side or Passenger Side
Material:steel
Fitment type:Direct replacement
Weight:13LB
Warranty:1 Year
Fits either LH (Driver Side) or RH (Passenger Side) Rear
Fits 4 lug Wheels
?
Vehicle Fitment
Fits Ford Fiesta 2011-2018
Item Include
2x wheel hub bearing
When do you need to replace
2X Rear Wheel Bearing Hub Assembly W/ABS For 2011-2018 Ford Fiesta 1.6L HA590367
Item Description:
Item Features
Condition:New
Placement on Vehicle：Driver Side or Passenger Side
Material:steel
Fitment type:Direct replacement
Weight:13LB
Warranty:1 Year
Fits either
LH (Driver Side) or RH (Passenger Side) Rear
Fits 4 lug Wheels
?
Vehicle Fitment
Fits Ford Fiesta 2011-2018
Item Include
2x
wheel hub bearing
When do you need to replace
Poor Clicking, snapping or popping
Clunking or knocking
Rumbling, humming or growling
Wobble and/or wheel vibrations
Shimmy, shudder, or vibration at constant speeds
Abnormal side pulling when applying brakes
Uneven or abnormal tire wear
ABS failure
How to Install
1.Loosen the lug nuts on the wheel of the hub bearing you're replacing with the breaking bar and a socket
2.Lift the wheel with the floor jack in a safe and secure manner. Support the vehicle on a jack stand
3.Remove the lug nuts and wheel.Locate the caliper bolts and remove them with the ratchet and a socket.
4.Pry the caliper off gently using a large straight-edged screwdriver and support the caliper on the coil spring with a bungee cord.
5.Locate the caliper bridge bolts (if applicable) and remove them with the ratchet and a socket.
6.Remove any ABS wires attached to the hub bearing assembly (if applicable) or unclip the wire and trace it to the plug.
7.Remove the spindle nut with the breaking bar and a spindle nut socket. Remove the washer behind the spindle nut.
8.Locate the wheel-bearing assembly bolts behind the knuckle, and loosen them with the breaking bar and socket.
9.Install the slide hammer onto the lug studs and secure with tightened lug nuts.Sand off the rust and corrosion around the knuckle with a fine- to medium-grade sandpaper.
10.Place the backing plate in its original position and place the new bearing onto the knuckle. Replace the wheel-bearing assembly bolts.
11.Replace washer and spindle nut and tighten to proper torque specifications with the half-inch drive torque wrench and spindle socket.
12.Replace the brakes in the same manner you extracted them. the tire and lug nuts, and tighten the lug nuts as tight as you can get them.
13.Lower the vehicle and tighten the lug nuts in an alternate fashion with the torque wrench and socket at the correct wheel nut specifications torque setting.
?
Note
If you have any question about the product, please contact us before buying, we will give you a best reply in time.
We are galde to offer quality service and vehicle parts to you, any sale questions please message us before open case or feedback, we will give you the best solution.
Fits Ford Fiesta 2011-2018
Item Specifics
Brand
Unbranded
Manufacturer Part Number
10269045
Placement on Vehicle
Front,Rear
Manufacturer Warranty
1 Year
Interchange Part Number
HA590367,29HA590367
OE/OEM Part Number
HA590367
Surface Finish
Polished, Rust Protected
Performance Part
Yes
Universal Fitment
No
Vintage Car Part
No
Flange Offset
2.7 inch
Items Included
2pc wheel bearing
Brake Pilot Diameter
2.5 inch
Material
Steel
With ABS Sensor
Yes
Superseded Part Number
WAHA590367,WBHA590367
Bolt Pattern
0.44 inch
Wheel Pilot Diameter
2.46 inch
Flange Diameter
5.16 inch
Type
Wheel Hub & Bearing Assembly
Suface
Polished, Rust Protected
About US:
We are committed to making the best auto-parts products and providing you with better services.
So if you have any quesiton or problem, please fell free to contact us about that.
Payment:
Paypal and other methods which can be accepted by eBay.
Shipping:
24-Hour handling time.
Product will be shipped within 2 business days after full payment is received and verified.
USPS, UPS, FedEx shipping will be provided.
Delivery time is about 2-8 business days to most of addresses.
Returns:
30-day free return provided.
Do
check the compatible chart or ask us about the compatibilities
before purchasing.
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Contact Us:
Any quesiton or problem, do contact us please.
We are always online to answer.
Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks.
DESCRIPTION
PAYMENT
SHIPPING
RETURN POLICY
CONTACT US
Shop Category
Store Home
Wheel Hub Bearing Assembly
Wheel Spacers
Hot Item
4PC 1" (25mm) Wheel Spacers Adapters 4x110 to 4x156 12x1.25 for Honda Foreman
USD 79.89
4PC 2" 5x4.5 5x114.3 Wheel Spacers For Jeep Wrangler Mercury Ford Ranger Mustang
USD 77.99
4PC 3" Hubcentric 5x4.75 Wheel Spacers for Chevy Camaro S10 Blazer GMC Sonoma
USD 145.99
Front Wheel Bearing & Hub for 10-17 Chevy Equinox Gmc Terrain Cadillac XTS CTS
USD 47.99
2X Front Wheel Hub & Bearing Assembly For Volkswagen Passat Jetta Tiguan Audi
USD 64.99
New List Item
2X Front Wheel Bearing & Hub Pair for Isuzu Chevrolet Colorado GMC Canyon
USD 116.99
2X Front Wheel Bearing for Chevrolet Uplander Saturn Buick Terraza
USD 70.99
2X Front Rear Right Left Side Wheel Hub Bearing Fits Cadillac Buick Oldsmobile
USD 62.99
2X Front Wheel Hub Bearing +2X CV Axle Shaft For Cadillac Escalade GMC Yukon
USD 305.99
2X Rear Wheel Bearing Hub w/ABS For 99-04 Pontiac Trans Montana Buick Chevy Olds
USD 70.99
Help & Info
Payment Policy
Shipping Policy
Return Policy
FAQ
About Us
2X Rear Wheel Bearing Hub Assembly W/ABS For 2011-2018 Ford Fiesta 1.6L HA590367
Item Description:
Item Features
Condition:New
Placement on Vehicle：Driver Side or Passenger Side
Material:steel
Fitment type:Direct replacement
Weight:13LB
Warranty:1 Year
Fits either
LH (Driver Side) or RH (Passenger Side) Rear
Fits 4 lug Wheels
?
Vehicle Fitment
Fits Ford Fiesta 2011-2018
Item Include
2x
wheel hub bearing
When do you need to replace
Poor Clicking, snapping or popping
Clunking or knocking
Rumbling, humming or growling
Wobble and/or wheel vibrations
Shimmy, shudder, or vibration at constant speeds
Abnormal side pulling when applying brakes
Uneven or abnormal tire wear
ABS failure
How to Install
1.Loosen the lug nuts on the wheel of the hub bearing you're replacing with the breaking bar and a socket
2.Lift the wheel with the floor jack in a safe and secure manner. Support the vehicle on a jack stand
3.Remove the lug nuts and wheel.Locate the caliper bolts and remove them with the ratchet and a socket.
4.Pry the caliper off gently using a large straight-edged screwdriver and support the caliper on the coil spring with a bungee cord.
5.Locate the caliper bridge bolts (if applicable) and remove them with the ratchet and a socket.
6.Remove any ABS wires attached to the hub bearing assembly (if applicable) or unclip the wire and trace it to the plug.
7.Remove the spindle nut with the breaking bar and a spindle nut socket. Remove the washer behind the spindle nut.
8.Locate the wheel-bearing assembly bolts behind the knuckle, and loosen them with the breaking bar and socket.
9.Install the slide hammer onto the lug studs and secure with tightened lug nuts.Sand off the rust and corrosion around the knuckle with a fine- to medium-grade sandpaper.
10.Place the backing plate in its original position and place the new bearing onto the knuckle. Replace the wheel-bearing assembly bolts.
11.Replace washer and spindle nut and tighten to proper torque specifications with the half-inch drive torque wrench and spindle socket.
12.Replace the brakes in the same manner you extracted them. the tire and lug nuts, and tighten the lug nuts as tight as you can get them.
13.Lower the vehicle and tighten the lug nuts in an alternate fashion with the torque wrench and socket at the correct wheel nut specifications torque setting.
?
Note
If you have any question about the product, please contact us before buying, we will give you a best reply in time.
We are galde to offer quality service and vehicle parts to you, any sale questions please message us before open case or feedback, we will give you the best solution.
Fits Ford Fiesta 2011-2018
Item Specifics
Brand :
Unbranded
Manufacturer Part Number :
10269045
Placement on Vehicle :
Front,Rear
Manufacturer Warranty :
1 Year
Interchange Part Number :
HA590367,29HA590367
OE/OEM Part Number :
HA590367
Surface Finish :
Polished, Rust Protected
Performance Part :
Yes
Universal Fitment :
No
Vintage Car Part :
No
Flange Offset :
2.7 inch
Items Included :
2pc wheel bearing
Brake Pilot Diameter :
2.5 inch
Material :
Steel
With ABS Sensor :
Yes
Superseded Part Number :
WAHA590367,WBHA590367
Bolt Pattern :
0.44 inch
Wheel Pilot Diameter :
2.46 inch
Flange Diameter :
5.16 inch
Type :
Wheel Hub & Bearing Assembly
Suface :
Polished, Rust Protected
About US:
We are committed to making the best auto-parts products and providing you with better services.
So if you have any quesiton or problem, please fell free to contact us about that.
Payment:
Paypal and other methods which can be accepted by eBay.
Shipping:
24-Hour handling time.
Product will be shipped within 2 business days after full payment is received and verified.
USPS, UPS, FedEx shipping will be provided.
Delivery time is about 2-8 business days to most of addresses.
Returns:
30-day free return provided.
Do
check the compatible chart or ask us about the compatibilities
before purchasing.
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Contact Us:
Any quesiton or problem, do contact us please.
We are always online to answer.
Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks.
All rights reserved.